Getting Familiar with Plumbing: Before Installing a Bathtub
Getting Familiar with Plumbing: Before Installing a Bathtub
Blog Article
Have you been on the lookout for content on A Step-by-Step Guide to Installing a Bathtub?
Mounting a bath tub isn't exactly brain surgery, but it does call for strong plumbing, woodworking, as well as sometimes, tiling abilities. Changing an old bath tub with a brand-new one is likewise a reasonably difficult task. If the old bathtub is easily obtainable, the project can relocate speedily; if you need to open a wall surface to remove the old tub and position the new bath tub, the task is much harder. In either situation, the project is within a home handyman's abilities, although you will need an assistant to move out the old tub and also embeded in the new one. Make sure you have certified on your own for the task as well as fit trying it. As opposed to working with a service provider to take control of a halfway-completed project, it is better to take into consideration utilizing one prior to you start. Opportunities are you may require an expert plumber to make tube connections.
This article will aid you set up a brand-new tub in your washroom if you have already gotten a new bathtub and do not require to alter the arrangement of your previous water system pipes.
Your tools and product list must make up the following:
Preparing for the Installation
Firstly, the sustaining frame supplied with the bathroom must be fitted (if required) according to the supplier's directions. Next, fit the faucets or mixer to the bath tub. When fitting the tap block, it is very important to make sure that if the faucet includes a plastic washer, it is fitted in between the bath as well as the taps. On a plastic bathroom, it is additionally practical to fit a sustaining plate under the faucets system to prevent strain on the bath tub.
Fit the versatile tap ports to the bottom of both taps using 2 nuts and also olives (in some cases provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet through the hole in the bathroom. Make use of the nut supplied by the maker to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bathroom. Ensure you make use of all of the supplied washing machines.
Attach the trap to the bottom of the waste outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Connect the bottom of the overflow tube in a similar manner.The bathroom should now be ready to be suited its last position.
Removing Old Taps
If you need to replace old taps with brand-new ones as a part of your installment, after that the first thing you ought to do is separate the water. After doing so, turn on the taps to drain any water staying in the system. The process of getting rid of the existing taps can be fairly troublesome because of the limited accessibility that is typically the case.
Use a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipelines to the taps. Have a cloth prepared for the continuing to be water that will originate from the pipes. Once the supply pipes have been removed, utilize the very same device to loosen the nut that holds the taps onto the bath/basin. You will certainly require to stop the solitary faucets from transforming during this procedure. Once the taps have actually been gotten rid of, the holes in the bath/basin will need to be cleaned up of any old securing substance.
Prior to proceeding to fit the new taps, contrast the pipeline links on the old taps to the brand-new taps. If the old faucets are longer than the new taps, then a shank adapter is required for the brand-new faucets to fit.
Installing the Bath tub
Using the two wooden boards under its feet, place the tub in the required position. The wood boards are helpful in equally spreading the weight of the tub over the location of the boards rather than focusing all the weight onto four tiny factors.
The following objective is to guarantee that the bathtub is leveled all round. This can be achieved by examining the level as well as changing the feet on the tub until the spirit level reads level.
To mount faucets, fit the bottom of the furthest adaptable faucet port to the appropriate supply pipeline by making a compression join; then do the exact same for the various other tap.
Turn on the water as well as check all joints and also brand-new pipework for leaks and also tighten them if essential. Fill up the bath tub as well as likewise examine the overflow electrical outlet and the typical outlet for leaks.
Ultimately, take care of the bath paneling as defined in the manufacturer's user's manual. Tiling and sealing around the bathtub should wait till the tub has actually been made use of at least when as this will settle it into its last placement.
Fitting New Taps
If the tails of the brand-new taps are plastic, then you will require a plastic port to avoid damage to the thread. One end of the port fits on the plastic tail of the tap and also the various other end offers a connection to the current supply pipelines.
If you need to fit a monobloc, after that you will call for reducing couplers, which connects the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
Next off, place the faucet in the placing opening in the bath/basin making certain that the washing machines are in area between the tap and also the sink. Safeguard the tap in place with the maker offered backnut. Once the faucet is firmly in place, the supply pipelines can be connected to the tails of the taps. The taps can either be attached by using corrugated copper piping or with normal tap connectors. The former type ought to be linked to the faucet ends initially, tightening only by hand. The supply pipelines can later be connected to the other end. Tighten up both ends with a spanner after both ends have actually been connected.
Tiling Around the Tub
In the location where the bath satisfies the floor tile, it is essential to secure the accompanies a silicone rubber caulking. This is very important as the fitting can relocate enough to break a stiff seal, triggering the water to pass through the wall surface between the bathroom as well as the tiling, leading to complications with dampness and also feasible leaks to the ceiling below.
You can select from a variety of coloured sealants to blend in your components and also installations. They are sold in tubes and also cartridges, and are capable of securing voids up to a size of 3mm (1/8 inch). If you have a bigger space to load, you can fill it with twists of soaked paper or soft rope. Keep in mind to constantly load the tub with water prior to sealing, to allow for the activity experienced when the bathtub remains in usage. The sealant can split fairly early if you do not think about this movement prior to sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are also easily readily available on the market. It is recommended to fit the floor tiles making use of water-resistant or waterproof adhesive as well as cement.
How to Install a Freestanding Bathtub?
Installing a freestanding bathtub or any kind of bathtub is not a difficult task if you have a sophisticated guide on installing a freestanding bathtub in your bathroom. Aside from getting the freestanding bathtub to your bathroom, you can do all the work without paying a plumber. A bathroom with a bathtub is a retreat where you can feel the sensation of coming home and soaking in that hot water. It is a great way to remove all the stress from your day.
This guide will walk you through installing a freestanding bathtub in simple steps and help you find relief.
Slope
Make sure your bathroom has a proper slope. If your floor lacks a slope, the water flow to the drain will not function, which leads to a blocked drain which can cost you money. You can use the level device to see your bathroom's vertical and horizontal aspects. Once you have that information, you must carry out the next step.
Placement
A freestanding bathtub has a unique characteristic that helps you bring elegance to your bathroom. A freestanding bathtub comes in various sizes and shapes suitable for different types of bathrooms.
According to the information you gathered from the level device, you must pick a bathtub that suits your style and fits your bathroom aesthetically. You can place a freestanding bathtub virtually anywhere, such as in the corner, near the wall, or even at the center of your bathroom. However, you must ensure proper plumbing where you want to install the tub. If not, then you must call a plumber.
Clean the bathroom floor
After deciding where to place the bathtub, you must clean the entire bathroom floor so that the dust and debris do not accumulate underneath the tub. Simple cleaning is enough, and you will clean it again after the installation.
Steps to Install a Freestanding Bathtub:
STEP 1: Place the protective blanket in the adjacent area where you want to install the bathtub. It will help you protect the bathtub's sides when you do the installation.
STEP 2: Now, place the 4x4 lumber in the area where you want to install the bathtub. Place the bathtub on top of the lumber, and align the drain line with the bathtub drain.
STEP 3: A freestanding bathtub comes with a drain kit. If not, make sure you purchase one with your bathtub. You can pop that drain kit and align it with your bathroom drain line. Ensure that you tighten the drain nut enough so there is no water leakage. You must also clean the bathtub’s drain to remove the factory dirt and debris.
STEP 4: Clean the drain hole in your bathroom. It helps to do the installation without any water blockage. A drain cleaner or bleach will suffice. Once the drain dries entirely, take a small amount of clear silicon and place it around the underside of the pipe flange.
STEP 5: Attach the drain tailpiece to the bottom of the bathtub. Place the rubber or plastic bushing with the plumbing material at the top of the tailpiece and screw the drain nut up the tube until it tightens both the bathtub’s drain and the drain tailpiece. Now you must add the lubricant to the seal to ensure there is no water leakage in the pipe connection.
STEP 6: Place caulk around the bottom edge of the bathtub. Take out the lumbar support and carefully bring the bathtub to the floor. Use a damp cloth to clean the excess caulk and debris and plumber putty to cover the tub drains and the floor.
Tips to Maintain a Freestanding Bathtub:
Always look for the clog in the drain. You can pull it out with a small stick if hair or debris is in the gutter. Use mild cleaning components, which will help you preserve the bathtub for a long time and will also help you remove surface-level scratches. Do not use strong solutions such as concentrated bleach to remove stains. Instead, mix water and diluted bleach with a ratio of 10:2, respectively. Apply it to the tub's surface and leave it for 15-20 minutes to remove any surface-level stains. Always check the floor drain. You may unclog it using any small sticks or a small vacuum to suck out all the debris. Check the heater or faucet immediately if you smell rust or grease in the water. Rust in the water may stain or damage the bathtub in the long run. If you want to sand the bathtub, try using 400 grit sandpaper or 600 grit sandpaper for a more refined finish.
Do you enjoy reading up on How to Install a Bathtub Yourself? Try to leave feedback below. We would be interested to find out your insights about this post. Hoping that you visit us again in the future. Sharing is caring. Helping others is fun. I cherish reading our article about How to Install a Bathtub Yourself.
Emergency plumber? One call away. Report this page